WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 34mm

- Plastic spoke covers in a variety of colors - 300mm cut to fit length - 36 pieces - enough for one wheel - Increases visibility and demands attention

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

The mounting solution for Thru Bolt rear wheels. Designed for an axle diameter of 10mm in the rear, the thru bolt system is a special kind of axle mounting for bikes. The DT Swiss thru bolt system is compatible with standard quick-release dropouts, but requires matching hubs. The stronger wheel connection results in greater stiffness. - Overall Length: 152mm - Thread Pitch: M10 x 1.0mm - Flat Washer

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

These rim valves are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager Tubeless Ready (TLR) wheels - Required for Bontrager's Tubeless Ready (TLR) system setup - Removable valve core for easy sealant fill - Silver MTB valve is compatible with all Bontrager Mountain wheels except: Line XXX, Kovee XXX, and Line Pro 40 - Alloy Road Tubeless Rim Valve is compatible with all Bontrager alloy TLR road wheels

On today's MTB frames, there are many diameters and width dropouts standards. Most Mavic wheels can be fitted with specific adapters to match with those frames: 142mm extenders for ITS-4 hubs, 142 mm extenders for TS-2 hubs and QR adapters (delivered with a front quick release) for all of them. - Converts a 12mm rear axle to fit in a frame with 9.5mm dropouts - Requires one pair per hub

- High-quality fat bike rim strips - Super durable PVC material

SPANK Industries Fratelli Tape is a special ultra-light polyamide, adhesive tubeless conversion tape, which is ideal for SPANK's patented OohBah profile rims. Thicker, less pliable tapes are often difficult or impossible when taping complex rim profiles. Fratelli tape makes tubeless set up simple, and adapts well to a variety of rim types, including sleeved and welded joints. 25mm width tape is suggested for rims up to 29mm internal width, and 30mm tape for rims 30mm internal width and greater. With adhesive properties unaffected in a wide temperature range, Fratelli tape is also perfect for winter riders, or those in exceptionally hot environments. - Material: Ultra Thin Polyamide - Width: 25mm or 30mm - Features: high temperature range adhesive, ideal for complex rim profile Installation: - Affix tape all the way around on the right side snug against the bead hook - Then repeat a second circumference around the left side, providing double-thick coverage over the spoke holes - Use a red-hot awl or similar to pierce the valve hole

Stan's All Mountain 29er Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!

When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Conical X12 washer, compatible with Syntace X-12 system - Thread Pitch: 12 x 1.0mm

Industry Nine Classic axle conversion kits include endcaps and axles to convert Pre-Torch hubs to various axle standards.

- Replacement rear skewer - Spacing: 135mm - Material: Steel

Whisky Parts Co. Tubeless Rim Tape.

Stan's Threaded Valve Extenders let you convert deep-section rims to tubeless. They're precision-machined from aluminum and are designed to fit deep-dish carbon and aluminum rims. And, they're threaded on the outside so you can install the Presta lock-ring nut for a perfect seal.

• Urethane coated nylon • High performance rim strips • 1 pair per box

- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Drive Side Axle End Cap

Stan's Olympic Rim Strip converts Stan's rims to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many BMX hubs - Type: Solid Axle - Threads: 9.5mm x 24tpi - Diameter: 9.5mm - Length: 180mm - 1 axle per bag

WTB's rim strips protect your tubes from rubbing against your rim. They are simple to install and they help reduce the chance of flats caused by friction between the tube and rim.